13.5kWh Tesla Powerwall 2 Home Battery

• ELECTRICAL SPECIFICATIONS
• Usable Capacity: 13.5 kWh
• Depth of Discharge: 100%
• Discharge Continuous: 5,000 watts (5 kW)
• Discharge Peak: 7,000 watts (7 kW)
• Charge Continuous: TBD kW
• DC Voltage: TBD Volts DC
• Maximum DC Current: TBD Amps
• Continuous DC Current: TBD Amps
• Round Trip Efficiency: 92.5% (beginning of life)
• ENVIRONMENTAL SPECIFICATIONS
• Operating Temperature Range: -20C (-4F) to +50C (+122F)
• Humidity: <95% condensing
• Maximum Altitude: 9,843 ft (3,000 m)
• Enclosure: Rated for indoor and outdoor installation
• Ingress Rating: IP35 & NEMA 3R (Powerwall), IP67 (battery Pod only)
• Impact Rating: IK09
• Storage Conditions:
• 24 hours: -30 °C to 60 °C (-22 °F to 140 °F)
• 1 Month: -20 °C to 45 °C (-4 °F to 113 °F)
• 12 Months: -20 °C to 30 °C (-4 °F to 86 °F), State of Energy (SoE): 50% initial
• MECHANICAL SPECIFICATIONS
• Dimensions L x W x D: 44" x 29" x 5.5" (1150mm x 755mm x 155mm)
• Weight: 264.4 lbs (110 kg)
• MINIMUM SPACE REQUIREMENTS
• Floor or wall mounted, Indoor or outdoor
• Total ceiling height: TBD ft ( mm)
• Height - Clearance above: TBD ft ( mm)
• Height - Clearance below: TBD ft ( mm)
• Lateral - Wall space: TBD in ( mm)
• Lateral - Clearance from each side: TBD in ( mm)
• Depth of workspace: TBD in ( mm)
• WARRANTY AND OTHER SPECIFICATIONS
• Warranty: 10 years
• Inverter: DC-AC inverter included.
• Certification: TBD, UL and IEC, Grid code compliant
• Tesla reserves the right to make product modifications at any time
• FreeCleanSolar is not responsible for ERRORS OR OMISSIONS
• Proper disposal of batteries is required. Refer to your local codes for disposal requirements.
• NOTE: The Tesla Installation Manual states that Powerwall must be installed by a Tesla Energy Certified Installer. Contact Tesla for details.

PV Solar Panel Tesla 2 Battery System Diagram

View the schematic below to see the components included in a PV solar system with StorEdge and Tesla Powerwall 2. Note: the Tesla Installation Manual states that Powerwall must be installed by a Tesla Energy Certified Installer. Contact Tesla for details.

Video Introduction for Tesla Energy Powerwall

Tesla Powerwall Installation Instructions

Read the entire INSTALLATION AND USER’S MANUAL document before installing or using Powerwall. Failure to do so or to follow any of the instructions or warnings can result in electrical shock, serious injury, or death, or can damage Powerwall, potentially rendering it inoperable. For the latest Powerwall documents, including the Warranty, visit Tesla. The Tesla Installation Manual states that Powerwall must be installed by a Tesla Energy Certified Installer. To secure the full 10-year product warranty, be sure to register Powerwall with Tesla.

• STEP 1 - REMOVE THE PALLET
• STEP 2 - DETERMINE THE MOUNTING LOCATION FOR POWERWALL
• STEP 3 - INSTALL THE WALL MOUNT BRACKET
• STEP 4 - MOUNT POWERWALL
• STEP 5 - REMOVE THE PACKAGING
• STEP 6 - REMOVE THE BOTTOM COVER
• STEP 7 - REMOVE THE SPLASH COVER
• STEP 8 - SET THE CONFIGURATION SWITCHES
• STEP 9 - SET THE ADDRESS SWITCHES
• STEP 10 - PREPARE THE WIRING
• STEP 11 - FEED WIRES THROUGH THE CONDUIT PLATE OR CABLE GLAND
• STEP 12 - CONNECT THE WIRING
• STEP 13 - CONNECT MULTIPLE POWERWALLS TOGETHER
• STEP 14 - CONNECT POWERWALL TO THE INVERTER
• STEP 15 - ATTACH THE SIDE COVERS
• STEP 16 - ATTACH THE SPLASH COVER
• STEP 17 - ATTACH THE BOTTOM COVER
• STEP 18 - REPACK THE SHIPPING BOX

TOOLS REQUIRED to install Tesla Powerwall

• Wall mount bracket fasteners
• Note: The details below are only guidance and are not guaranteed to be applicable. Consult local building codes and a structural engineer to ensure the use of appropriate fasteners.
  • Minimum of 6 fasteners, stainless steel, diameter 10 mm (3/8 in)
  • Fastener head clearance for all positions but two bottom outer holes: 18 mm (11/16 in)
  • Fastener head clearance for bottom two holes at 600 mm (24 in) spacing: 8 mm (5/16 in)
  • Washers between fastener heads and wall mount bracket are recommended
• Drill and a drill bit suitable for drilling pilot holes in the desired mounting surface
• Socket wrench
• 10 mm socket adapter (for covers and wall mount bracket side tabs)
• 17 mm socket adapter (for wood block bolts)
• Large flathead screwdriver (for ground lug)
• Optional: small flathead screwdriver (for wiring terminal tabs)
• T20 Torx (for splash cover)
• T25 Torx (for screws fastening box to wood blocks)
• T30 Torx (for packaging L-bracket and conduit/gland plate)
• Torque wrench
• Stud finder (for wood installations)
• Level tool
• Painter's tape and/or pencil
• Wire stripper and wiring (as described in Step 10)
• Conduit fitting or cable gland (as appropriate)
• Lift tool or adequate personnel trained and capable of lifting 115 kg (254 lb) from ground level to approximately chest height. Warning: Powerwall is heavy and challenging to lift. Lift equipment is recommended.
• To prevent injury, wear work boots (preferably steel-toed), long pants, and gloves.