8.1kW PV Kit SolarWorld 300, Optimizers, Tesla Battery

• Your Grid-Tied PV Power System from SolarWorld will include:
• (27) SolarWorld SunModule Plus 300 watt model SW300 Mono
• (27) SolarEdge Power Optimizers model P300
• (1) StorEdge inverter SE7600A-USS
• (1) Integrated safety switch disconnect box
• (1) Tesla Powerwall 6.4 kWh home battery
• (1) SolarEdge 5 KVA auto-transformer for off-grid backup power
• (1) SolarEdge Power Meter for smart energy management
• (1) SolarEdge Home Gateway lifetime monitoring communication kit
• (2) x 50' PV wires with MC4 connectors
• Rooftop rack system, 2 row X 14 column layout, portrait orientation, flush mount setup
• Mounting rails, splices, and grounding lugs
• Module grounding mid-clamps and end-clamps
• L-feet attachments with hardware
• QuickMount PV water-tight aluminum flashing or Schletter tile roof hooks
• NEC code compliant PV wiring labels
• PV system permit plans, product data sheets, warranty certificates and installation instruction manuals
• WARRANTY AND SUPPORT
• 10 year product, 25 year performance warranty on solar panels
• 12 year product warranty on inverter, optional 25 year extended warranty available
• 25 year product warranty on optimizers
• 10 year product warranty on battery
• Lifetime technical support from FreeCleanSolar and Manufacturers
• PV ARRAY SYSTEM SPECIFICATIONS
• Maximum Power DC (Wp): 8,100 watts DC; 8.1 kW
• Maximum Power AC (Wp): 7,166 watts AC
• Estimated Power Generated: 980 kWh AC monthly average
• Maximum Battery Power: 6.4 kWh per daily cycle
• Maximum Power Voltage Vmp (V): 240V
• Maximum System Output Current Imp (A): 32 Amps
• MinImum String Length single-phase: 8 panels
• Maximum String Length single-phase: 15 panels
• Maximum Power per String single-phase: 5,250 watts DC STC
• Array Dimensions: 490 square feet
• Array Weight: 1,250 lbs
• Distributed Load: 2.6 lbs psf
• Structural Design Criteria: ASCE 7-10
• Wind Speed Rating: 110 mph
• Snow Load: 20 lbs psf
• HOME BATTERY ELECTRICAL SPECIFICATIONS
• Energy Output: 6.4 kWh daily cycle
• Discharge Continuous: 3.3 kW
• Discharge Peak: 3.3 kW
• Charge Continuous: 3.3 kW
• DC Voltage: 350 - 450 Volts DC
• Maximum DC Current: 9.5 Amps
• Continuous DC Current: 9.5 Amps
• Round Trip Efficiency: 92.5% (beginning of life)
• BATTERY ENVIRONMENTAL SPECIFICATIONS
• Operating Temperature Range: -20C (-4F) to +50C (+122F)
• Humidity: <95% condensing
• Maximum Altitude: 9,843 ft (3,000 m)
• Enclosure: Rated for indoor and outdoor installation
• Ingress Rating: IP35 & NEMA 3R (Powerwall), IP67 (battery Pod only)
• Impact Rating: IK09
• Storage Conditions:
• 24 hours: -30 °C to 60 °C (-22 °F to 140 °F)
• 1 Month: -20 °C to 45 °C (-4 °F to 113 °F)
• 12 Months: -20 °C to 30 °C (-4 °F to 86 °F), State of Energy (SoE): 50% initial
• BATTERY MECHANICAL SPECIFICATIONS
• Dimensions: 51.3" x 34" x 7.2" (1302mm x 862mm x 183mm)
• Weight: 210 lbs (95 kg)
• BATTERY MINIMUM SPACE REQUIREMENTS
• Total ceiling height: 6.5 ft (2000 mm)
• Height - Clearance above: 1 ft (300 mm)
• Height - Clearance below: 1 ft (300 mm)
• Lateral - Wall space: 42 in (1070 mm)
• Lateral - Clearance from each side: 4 in (100 mm)
• Depth of workspace: 6 in (153 mm)
• BATTERY WARRANTY AND OTHER SPECIFICATIONS
• Warranty: 10 years
• Certification: NRTL listed to UL standards
• Tesla reserves the right to make product modifications at any time
• FreeCleanSolar is not responsible for ERRORS OR OMISSIONS
• Proper disposal of batteries is required. Refer to your local codes for disposal requirements.
• SOLAR PANEL SPECIFICATIONS
• STC DC Watts Maximum Power: 300.0 W
• PTC DC Watts Maximum Power: 272.2 W
• NOCT DC Watts Nominal Power: 224.1 W
• Module Efficiency: 17.89%
• Maximum Power Voltage Vmp (V): 31.6V
• Maximum Power Current Imp (A): 9.57A
• Open Circuit Voltage Voc (V): 40.1V
• Short Circuit Current Isc (A): 10.23A
• Maximum system voltage: 1000V UL, 1000V IEC
• Maximum reverse current: 25A
• Power Tolerance 0 +5 watts
• Cells per module: 60
• Cell Technology Type: Monocrystalline, 5 bus bar
• Frame: Anodized Aluminum Alloy, Silver frame
• Glass: Low iron tempered with Anti-Reflective Coating
• Dimensions: 65.95 x 39.4 x 1.29 inches (33mm)
• Weight: 39.7 lbs
• Junction Box: IP65 Class
• Connector Type: PV wire per UL4703 with H4 connectors
• Output cables: 36.61 inches
• Product Warranty: 10 years material and workmanship
• Performance Guarantee: 25 years power output
• Fire Safety Classification: Class C
• Certifications: UL 1703, California CEC, IEC 61215, IEC/EN 61730
• Operating Temperature Range: -40F to 185F
• Nominal Operating Cell Temperature NOCT: 113 degrees F +/- 2 degrees
• Front Load (snow) Test: 113 PSF
• Rear static load (wind) test: 5400Pa
• Design Loads - Two rail system: 113 psf downward, 64 psf upward
• Design Loads - Three rail system: 178 psf downward, 64 psf upward
• Design Loads - Edge mounting: 178 psf downward, 41 psf upward
• Hailstone impact test: 1 inch hail at 23M/s from 1m distance

DIY or Full-Service Pro Solar Installation

You can choose how to install the solar panel system. You can Do-It-Yourself (DIY), hire any contractor or handyman for labor, or we can provide Full-Service Professional installation. Most customers choose DIY to save some serious money. However you decide to go solar, we will provide the permit plans, instruction manuals and lifetime technical support. You will also have the same manufacturer warranties, and be eligible for tax credits, rebates and other incentives.

Full-Service, Professional solar panel system installation by a state licensed contractor includes labor, wiring, electrical setup, balance of system parts, building permit, utility approval, inspection, monitoring setup, and activation. 5 to 10 year warranty on labor. Installation services are not subject to state sales tax. Final price subject to system design and site visit. Additional fees may apply for electrical panel upgrade, multiple roof areas, conduit wiring greater than 100 ft, two or more story property, or tilt mounting.

StorEdge Tesla Battery System Diagram

View the schematic below to see the components included in a PV solar system with StorEdge and Tesla Powerwall. Note: the Tesla Installation Manual states that Powerwall must be installed by a Tesla Energy Certified Installer. Contact Tesla for details.

How to Install the PV Electric System with SolarEdge Optimizers

1. Read and follow the installation instruction manuals provided with the solar panel, the inverter and the mounting
2. Secure the roof attachment standoffs and flashing to the roof rafter joists; add caulk as needed
3. Attach mounting rails to the roof attachment standoffs using supplied hardware
4. Attach the module optimizers to the rails using the supplied hardware and connect the optimizer output cables into desired strings as indicated in the electrical line drawing
5. Connect PV wires and ground cable from the rooftop junction box or safety switch to the solar inverter
6. Connect the inverter to an open circuit breaker in the household electrical box. Place the circuit breaker in the OFF position. The breaker size should conform to NEC standards.
7. Secure the solar panels to the mounting rails using the supplied mid-clamps and end-clamps
8. Connect the solar panel output cables to the module optimizers
9. Connect the last PV cable to a junction box or Safety Switch disconnect box
10. Contact the local building department or electric utility company to schedule inspection prior to connection to the grid

Tools Required to Install Rooftop Solar Mounting

• Tape measure
• Roofers bar, shingle ripper
• Chalk line
• Stud finder
• Caulking gun
• Sealant compatible with roofing materials
• Drill with 7/32" long-style bit
• Drill or impact gun with 1/2" deep socket
• Ladder, safety harness and rope

How to Install Solar Panel QuickMount Roof Flashing Attachments

Simply slide the flashing under a row of roof shingles, drill pilot hole, apply sealant to hole, secure with bolt and attach sealing washer. Just a few minutes to install QuickMount PV. Watch this video for a demonstration.

Installation Video Guide for Rooftop Solar Mounting

How to Install SolarEdge Optimizers

This 5 minute video demonstrates how to install a solar edge inverter and optimizer system step-by-step.

Tesla Powerwall Installation Instructions

Read the entire INSTALLATION AND USER’S MANUAL document before installing or using Powerwall. Failure to do so or to follow any of the instructions or warnings can result in electrical shock, serious injury, or death, or can damage Powerwall, potentially rendering it inoperable. For the latest Powerwall documents, including the Warranty, visit Tesla.

The Tesla Installation Manual states that Powerwall must be installed by a Tesla Energy Certified Installer. To secure the full 10-year product warranty, be sure to register Powerwall with Tesla.

• STEP 1 - REMOVE THE PALLET
• STEP 2 - DETERMINE THE MOUNTING LOCATION FOR POWERWALL
• STEP 3 - INSTALL THE WALL MOUNT BRACKET
• STEP 4 - MOUNT POWERWALL
• STEP 5 - REMOVE THE PACKAGING
• STEP 6 - REMOVE THE BOTTOM COVER
• STEP 7 - REMOVE THE SPLASH COVER
• STEP 8 - SET THE CONFIGURATION SWITCHES
• STEP 9 - SET THE ADDRESS SWITCHES
• STEP 10 - PREPARE THE WIRING
• STEP 11 - FEED WIRES THROUGH THE CONDUIT PLATE OR CABLE GLAND
• STEP 12 - CONNECT THE WIRING
• STEP 13 - CONNECT MULTIPLE POWERWALLS TOGETHER
• STEP 14 - CONNECT POWERWALL TO THE INVERTER
• STEP 15 - ATTACH THE SIDE COVERS
• STEP 16 - ATTACH THE SPLASH COVER
• STEP 17 - ATTACH THE BOTTOM COVER
• STEP 18 - REPACK THE SHIPPING BOX

TOOLS REQUIRED to install Tesla Powerwall

• Wall mount bracket fasteners
• Note: The details below are only guidance and are not guaranteed to be applicable. Consult local building codes and a structural engineer to ensure the use of appropriate fasteners.
  • Minimum of 6 fasteners, stainless steel, diameter 10 mm (3/8 in)
  • Fastener head clearance for all positions but two bottom outer holes: 18 mm (11/16 in)
  • Fastener head clearance for bottom two holes at 600 mm (24 in) spacing: 8 mm (5/16 in)
  • Washers between fastener heads and wall mount bracket are recommended
• Drill and a drill bit suitable for drilling pilot holes in the desired mounting surface
• Socket wrench
• 10 mm socket adapter (for covers and wall mount bracket side tabs)
• 17 mm socket adapter (for wood block bolts)
• Large flathead screwdriver (for ground lug)
• Optional: small flathead screwdriver (for wiring terminal tabs)
• T20 Torx (for splash cover)
• T25 Torx (for screws fastening box to wood blocks)
• T30 Torx (for packaging L-bracket and conduit/gland plate)
• Torque wrench
• Stud finder (for wood installations)
• Level tool
• Painter's tape and/or pencil
• Wire stripper and wiring (as described in Step 10)
• Conduit fitting or cable gland (as appropriate)
• Lift tool or adequate personnel trained and capable of lifting 115 kg (254 lb) from ground level to approximately chest height. Warning: Powerwall is heavy and challenging to lift. Lift equipment is recommended.
• To prevent injury, wear work boots (preferably steel-toed), long pants, and gloves.